Информация по замене по сервис мануалу - коробки без щупа. Если коротко - то замена при температуре 35-45 градусов.
Замена происходит в 2 замены - слил-залил по 3 литра.
A/T FLUID
AT-15
< SERVICE INFORMATION > [5AT: RE5R05A]
A/T FLUID
Changing A/T Fluid INFOID:0000000005906090
CAUTION:
• If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used.
• Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and A/T
durability, and may damage the A/T, which is not covered by the warranty.
• When filling ATF, be careful not to scatter heat generating parts such as exhaust.
1. Step 1
a. Install the O-ring (315268E000) (A) to the charging pipe
(310811EA5A) (B).
2. Step 2
a. Use CONSULT-III to check that the ATF temperature is 40°C (104°F) or less.
b. Lift up the vehicle.
c. Remove the drain plug from the oil pan, and then drain the ATF.
d. When the ATF starts to drip, temporarily tighten the drain plug to the oil pan.
NOTE:
Never replace drain plug and drain plug gasket with new ones yet.
e. Remove overflow plug from oil pan.
f. Install the charging pipe (A) to the overflow plug hole.
CAUTION:
Tighten the charging pipe by hand.
g. Install the bucket pump hose (B) to the charging pipe.
CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
h. Fill approximately 3 liters (2-5/8 lmp qt) of the ATF.
i. Remove the bucket pump hose to remove the charging pipe,
and then temporarily tighten the overflow plug to the oil pan.
CAUTION:
Quickly perform the procedure to avoid ATF leakage from
the oil pan.
j. Lift down the vehicle.
k. Start the engine and wait for approximately 3 minutes.
l. Stop the engine.
3. Step 3
a. Repeat ”Step 2”.
4. Final Step
a. Use CONSULT-III to check that the ATF temperature is 40°C (104°F) or less.
b. Lift up the vehicle.
c. Remove the drain plug from the oil pan, and then drain the ATF.
Recommended fluid and fluid capacity : Refer to AT-278, "General Specification".
JSDIA1334ZZ
JSDIA1335ZZ
AT-16
< SERVICE INFORMATION > [5AT: RE5R05A]
A/T FLUID
d. When the ATF starts to drip, tighten the drain plug to the oil pan to the specified torque. Refer to AT-199,
"Control Valve with TCM".
CAUTION:
Never reuse drain plug and drain plug gasket.
e. Remove overflow plug from oil pan.
f. Install the charging pipe (A) to the overflow plug hole.
CAUTION:
Tighten the charging pipe by hand.
g. Install the bucket pump hose (B) to the charging pipe.
CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
h. Fill approximately 3 liters (2-5/8 lmp qt) of the ATF.
i. Remove the bucket pump hose to remove the charging pipe,
and then temporarily tighten the overflow plug to the oil pan.
CAUTION:
Quickly perform the procedure to avoid ATF leakage from
the oil pan.
j. Lift down the vehicle.
k. Start the engine.
l. Make the ATF temperature approximately 40°C (104°F).
NOTE:
The ATF level is greatly affected by the temperature. Always check the ATF temperature on ”ATF TEMP
1” of ”Data Monitor” using CONSULT-III.
m. Park vehicle on level surface and set parking brake.
n. Shift the selector lever through each gear position. Leave selector lever in ”P” position.
o. Lift up the vehicle when the ATF temperature reaches 40°C (104°F), and then remove the overflow plug
from the oil pan.
p. When the ATF starts to drip, tighten the overflow plug to the oil pan to the specified torque. Refer to AT-
199, "Control Valve with TCM".
CAUTION:
Never reuse overflow plug.
Adjusting A/T Fluid INFOID:0000000005906091
CAUTION:
• If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used.
• Using ATF other than Genuine NISSAN Matic S ATF will cause deterioration in driveability and A/T
durability, and may damage the A/T, which is not covered by the warranty.
• When filling ATF, be careful not to scatter heat generating parts such as exhaust.
• Always maintain the ATF temperature within between 35°C (95°F) and 45°C (113°F) while checking
with CONSULT-III when the ATF level adjustment is performed.
1. Install the O-ring (315268E000) (A) to the charging pipe
(310811EA5A) (B).
2. Start the engine.
3. Make the ATF temperature approximately 40°C (104°F).
NOTE:
The ATF level is greatly affected by the temperature. Always
check the ATF temperature on ”ATF TEMP 1” of ”Data Monitor”
using CONSULT-III.
4. Park vehicle on level surface and set parking brake.
5. Shift the selector lever through each gear position. Leave selector
lever in ”P” position.
6. Lift up the vehicle.
JSDIA1335ZZ
Recommended fluid and fluid capacity : Refer to AT-278, "General Specification".
JSDIA1334ZZ
A/T FLUID
AT-17
< SERVICE INFORMATION > [5AT: RE5R05A]
7. Check the ATF leakage from transmission.
8. Remove overflow plug from oil pan.
9. Install the charging pipe (A) to the overflow plug hole.
CAUTION:
Tighten the charging pipe by hand.
10. Install the bucket pump hose (B) to the charging pipe.
CAUTION:
Insert the bucket pump hose all the way to the end of the
charging pipe.
11. Fill approximately 0.5 liters (1/2 lmp qt) of the ATF.
12. Check that the ATF leaks when removing the charging pipe and
the bucket pump hose. If the ATF does not leak, refill the ATF.
13. When the ATF starts to drip, tighten the overflow plug to the oil
pan to the specified torque. Refer to AT-199, "Control Valve with TCM".
CAUTION:
Never reuse overflow plug.
Добавлено через 5 минут
http://akppspbcentr.ru/akpp-jatco-nissan-re5r05a-jr507e
Вступить в клуб
Карта сайта 
Контакты 
позже еще раз контрольная замена! лучше потратить 20 000 руб чем тысяч 100-150!!!
